E1108ACBG-8E-E Detailed Introduction
E1108ACBG-8E-E is a high-performance Ethernet switching chip, widely used in enterprise networks, data centers, industrial control and other fields. This chip is known for its high bandwidth, low latency, rich management functions and high reliability. This article will introduce the technical parameters, performance characteristics and application scenarios of E1108ACBG-8E-E in detail.
E1108ACBG-8E-E Technical Parameters
Architecture: Based on high-performance Ethernet switching architecture
Operating voltage: 3.3V
Operating frequency: up to 250MHz
Number of ports: 8 10/100/1000Mbps Ethernet ports
MAC address table: supports 16K entries
Buffer: 1.5MB SRAM
Protocol support:
- IEEE 802.3 10BASE-T
- IEEE 802.3u 100BASE-TX
- IEEE 802.3ab 1000BASE-T
- IEEE 802.1Q VLAN
- IEEE 802.1p QoS
- IEEE 802.1D Spanning Tree Protocol (STP)
- IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
- IEEE 802.1s Multiple Spanning Tree Protocol (MSTP)
- IEEE 802.3ad Link Aggregation Control Protocol (LACP)
Low power mode: Support EEE (Energy Efficient Ethernet)
E1108ACBG-8E-E Performance Features
High bandwidth:
- Supports 8 10/100/1000Mbps Ethernet ports, providing high-speed data transmission capabilities.
- The total bandwidth is up to 16Gbps, meeting the needs of high-traffic networks.
Low latency:
- Built-in high-performance switching engine to ensure fast forwarding of data packets, with latency as low as microseconds.
Rich management functions:
- CLI (Command Line Interface): Supports configuration and management through the command line.
- Web interface: Provides a friendly Web management interface for users to perform graphical configuration.
- SNMP (Simple Network Management Protocol): Supports SNMP v1/v2c/v3 for centralized management and monitoring.
High reliability:
- Redundant power supply support: Supports dual power input to improve system reliability.
- Loop protection: Supports loop detection and prevention to avoid network storms.
- Link aggregation: Supports IEEE 802.3ad LACP to improve bandwidth and redundancy.
Advanced functions:
- VLAN support: Support IEEE 802.1Q VLAN to achieve network isolation and management.
- QoS (Quality of Service): Support IEEE 802.1p QoS to ensure priority transmission of key services.
- Security functions: Support port security, MAC address filtering, 802.1X authentication, etc. to enhance network security.
- Flow control: Support flow control in full-duplex and half-duplex modes to avoid data congestion.
Low power consumption:
- EEE (Energy Efficient Ethernet): Support EEE standard, reduce power consumption when idle, energy saving and environmental protection.
E1108ACBG-8E-E application scenarios
Enterprise network:
- Office network: Suitable for enterprise office network, providing high-speed and stable network connection.
- Data center: Suitable for high-speed interconnection between servers and storage devices within the data center.
Industrial control:
- Industrial automation: Suitable for industrial automation systems, providing real-time data transmission and high reliability.
- Intelligent manufacturing: Support high-speed communication between intelligent manufacturing equipment to improve production efficiency.
Education and research:
- Campus network: Applicable to campus network, providing high-speed and stable network connection, supporting a large number of terminal devices.
- Scientific research institutions: Applicable to the high-performance computing and data transmission needs of scientific research institutions.
Health care:
- Hospital network: Applicable to high-speed interconnection between medical equipment and information systems within the hospital.
- Telemedicine: Support high-speed data transmission of telemedicine equipment to improve the efficiency of medical services.
Telecom operators:
- Metropolitan area network: Applicable to the access and aggregation layer of the metropolitan area network, providing high-speed and stable network connection.
- Broadband access: Support broadband access equipment and provide high-speed Internet connection.
Precautions for using E1108ACBG-8E-E
Power management:
- Ensure that the power supply voltage is within the 3.3V range to avoid chip damage caused by overvoltage or undervoltage.
- Use a regulated power supply to ensure the stability and reliability of the power supply.
Programming and debugging:
- Use the official programming tools and debugging software to ensure the correctness and stability of the program.
- Read the chip manual carefully to understand the various registers and configuration options.
Pin configuration:
- Read the chip manual carefully, configure the pin function correctly, and avoid conflicts and misoperation.
- Use appropriate pin protection measures to prevent static electricity and overcurrent damage.
Protection measures:
- Pay attention to anti-static, moisture-proof and dust-proof during use to ensure the long-term stability and reliability of the chip.
- Regular inspection and maintenance to ensure the normal operation of the system.
Temperature management:
- Avoid using in an environment beyond the operating temperature range to avoid affecting performance and life.
- Use appropriate heat dissipation measures to ensure that the chip works normally in a high temperature environment.
Why choose EDE1108ACBG-8E-E?
The EDE1108ACBG-8E-E stands out for its balanced design, combining high performance with manageable power requirements, making it an ideal choice for applications that require consistent speed and durability. Its compatibility with the DDR2 standard ensures that it can be seamlessly integrated into systems that require fast, low-latency memory while maintaining signal integrity and stability
Elpida E1108acbg-8E-E chip Datasheet
Click to view the table:
Elpida E1108acbg-8E-E chip Datasheet PDF
Future prospects of E1108ACBG-8E-E
- Higher bandwidth: Further improve bandwidth and transmission rate by improving core architecture and manufacturing process.
- Lower latency: Optimize packet processing algorithms to further reduce latency.
- More management functions: Integrate more advanced management functions, such as AI-assisted management and automatic optimization.
- Smarter control: Integrate sensors and communication modules to achieve smarter network management and fault prediction.
Conclusion
E1108ACBG-8E-E is a high-performance Ethernet switching chip. With its high bandwidth, low latency, rich management functions and high reliability, it is widely used in enterprise networks, data centers, industrial control and other fields. Users can choose the appropriate model according to their specific needs to ensure the excellent performance of the system in network connection.
Statement:
All articles (images, texts, audio) on this site are uploaded and shared by users, or integrated from relevant internet sources, only for user's learning. If your rights are violated, please contact the administrator to delete! Link to this article: https://www.jinftry.com.
FAQs
What is the E1108ACBG-8E-E component?
It is a DDR2 SDRAM memory chip with a 1 Gbit density, organized as 128M x 8. It is designed for high-performance applications, offering 800 Mbps data rates and compatibility with SSTL_18 interfaces.
Who manufactures the E1108ACBG-8E-E?
This component is produced by Elpida Memory Inc., a company specializing in memory solutions.
What are its key features?
- 1.8V operating voltage
- Differential clock inputs
- On-Die Termination (ODT) for improved signal integrity
- Supports auto and self-refresh cycles for data retention
What applications is it suitable for?
It is ideal for use in computing systems, consumer electronics, and other environments requiring efficient memory management.
What is the package type?
The E1108ACBG-8E-E uses a 60-pin FBGA (Fine Ball Grid Array) package, which ensures compactness and reliability.
Is it RoHS compliant?
Yes, it complies with the EU RoHS Directive (2002/95/EC), which restricts the use of hazardous substances.
What is the maximum operating temperature?
The chip can function in temperatures up to 95°C, with a refresh period adjustment above 85°C.
How is data accessed?
It uses a double-data-rate architecture, enabling two data transfers per clock cycle. Burst lengths of 4 and 8 are supported for efficient data handling.
What clock rates does it support?
The component supports clock rates necessary to achieve data rates of 667 Mbps and 800 Mbps.
Is this part readily available?
Availability depends on the supplier. Many distributors list it as a legacy part, suggesting limited stock in modern markets.